 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ACA2407E 750/870 MHz CATV Power Doubler Line Amplifier Data Sheet - Rev 2.1 FEATURES * * * * * * * * * 21.3 dB Gain Very Low Distortion Excellent 75 Input and Output Match Stable with High VSWR Load Conditions Monolithic Design for Consistent Performance Part-to-Part Low DC Power Consumption Surface Mount Package Compatible with Automatic Assembly Low Cost Alternative to Hybrids Meets Cenelec Standards APPLICATIONS * CATV Line Amplifiers, System Amplifiers, Distribution Nodes S7 Package 16 Pin Wide Body SOIC with Heat Slug PRODUCT DESCRIPTION The ACA2407E is a highly linear, monolithic GaAs RF amplifier that has been developed to replace, in new designs, standard CATV hybrid amplifiers. Offered in a convenient surface mount package, the MMIC consists of two pairs of parallel amplifiers that are optimized for exceptionally low distortion and noise figure. A hybrid equivalent that provides flat gain response and excellent input and output return loss over the 40 to 870 MHz CATV downstream band is formed when one ACA2407E is cascaded between two appropriate transmission line baluns. 1A RF Input 2A RF Output 1B 2B ACA2407E Figure 1: Hybrid Application Diagram 12/2002 ACA2407E 1 2 3 4 5 6 7 8 GND 2A IN GND 1A IN 1BIN ISET 2B IN GND Figure 2: Pin Out GND 1A OUT Bias 1A 2A OUT 2B OUT Bias 1B 1BOUT GND 16 15 14 13 12 11 10 9 Table 1: Pin Description PIN 1 2 3 4 5 6 7 8 NAME GND 2AIN GND 1AIN 1BIN ISET 2BIN GND DESCRIPTION Ground Amplifier 2A Input Ground Amplifier 1A Input Amplifier 1B Input Current Adjust Amplifier 2B Input Ground PIN 9 10 11 12 13 14 15 16 NAME GND 1BOUT B i as 1B 2BOUT 2AOUT B i as 1A 1AOUT GND DESCRIPTION Ground Amplifier 1B Output Bias for 1B Amplifier Amplifier 2B Output and Supply Amplifier 2A Output and Supply Bias for 1A Amplifier Amplifier 1A Output Ground 2 Data Sheet - Rev 2.1 12/2002 ACA2407E ELECTRICAL CHARACTERISTICS Table 2: Absolute Mimimum and Maximum Ratings PARAMETER Supply (pins 12, 13) RF Power at Inputs (pins 4, 5) Storage Temperature Soldering Temperature Soldering Time MIN 0 -65 - MAX +28 +75 +150 +260 5.0 UNIT VD C dBmV C C S ec Stresses in excess of the absolute ratings may cause permanent damage. Functional operation is not implied under these conditions. Exposure to absolute ratings for extended periods of time may adversely affect reliability. Notes: 1. Pins 2, 4, 5 and 7 should be AC-coupled.No external DC bias should be applied. 2. Pin 6 should be AC-grounded and/or pulled to ground through a resistor for current control. 3. Pins 11 and 14 are bias feeds for input amplifiers 1A and 1B. No external DC bias should be applied. 4. Pins 10 and 15 receive DC bias directly from pins 11 and 14. Table 3: Operating Ranges PARAMETER Supply: VDD (pins 12, 13) Voltage at ISET (pin 6) RF Frequency Case Temperature MIN 40 -40 TYP +24 +3 - MAX 870 +110 UNIT VD C VD C MHz C The device may be operated safely over these conditions; however, parametric performance is guaranteed only over the conditions defined in the electrical specifications. Data Sheet - Rev 2.1 12/2002 3 ACA2407E Table 4: Electrical Specifications (TA = +25 C, VDD = +24 VDC) PARAMETER Gain (1) Cable Equivalent Slope Gain Flatness Noise Figure (1) (1) MIN 20.4 18 410 - TYP 21.3 0 0.2 4.0 -70 -65 -66 -60 -62 -60 22 425 3.1 <1 MAX 22.4 4.5 -66 -64 -60 440 3.8 - UNIT dB dB dB dB COMMENTS to 750 MHz (1) CTB (1) 77 Channels (2) 110 Channels (3) CSO (1) 77 Channels (2) 110 Channels (3) XMOD (1) 77 Channels (2) 110 Channels (3) Return Loss (Input/Output) (1) Supply Current (IDD) Thermal Resistance IDD Adjust dB c dB c dB c dB mA o 75 system R1 = 75 k , R3 open Refer to Figure 8 C/W mA Refer to Figure 8 Notes: (1) Measured with baluns on the input and output of the device. (2) Parts measured with 77 channels, +56 dBm V power, 13.5 dB tilt at 870 MHz. (3) Parts measured with 110 channels, +52 dBm V power, 13.5 dB tilt at 870 MHz. 4. All specifications as measured on Evaluation Board (see Figures 7 & 8). 4 Data Sheet - Rev 2.1 12/2002 ACA2407E Table 5: Electrical Specifications at Reduced IDD (TA = +25 C, VDD = +24 VDC) PARAMETER Gain CTB (1) 77 Channels CSO (1) 77 Channels XMOD (1) 77 Channels (2) TYP 21.0 -58 -60 -50 360 Open 10 k TYP 21.2 -64 -62 -55 390 Open Open UNIT dB dB c dB c dB c mA COMMENTS (2) (2) Supply Current (IDD) R1 (Figure 8) R3 (Figure 8) Notes: (1) Measured with baluns on the input and output of the device. (2) Parts measured with 77 channels, +56 dBm V power, 13.5 dB tilt at 870 MHz. Data Sheet - Rev 2.1 12/2002 5 ACA2407E PERFORMANCE DATA Figure 3: Noise Figure vs. Frequency 5 4.5 Noise Figure (dB) 4 3.5 3 2.5 2 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Figure 4: Gain (S21) vs. Frequency 24 23.5 23 22.5 Gain (dB) 22 21.5 21 20.5 20 19.5 19 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) 6 Data Sheet - Rev 2.1 12/2002 ACA2407E Figure 5: Input and Output Return Loss (S11 and S22) vs. Frequency 5 0 -5 Return Loss (dB) -10 -15 -20 -25 -30 -35 -40 0 100 200 300 400 500 600 700 800 900 1000 S11 S22 Frequency (MHz) Figure 6: Isolation (S12) vs. Frequency 0 -5 -10 -15 Isolation (dB) -20 -25 -30 -35 -40 -45 -50 0 100 200 300 400 500 600 700 800 900 1000 Frequency (MHz) Data Sheet - Rev 2.1 12/2002 7 ACA2407E APPLICATION INFORMATION Figure 7: Evaluation Board Layout C4 1 2 RF IN 3 16 15 14 R2 +24 V Vt GND 2AIN GND 1AIN 1BIN ISET 2BIN GND ACA2407E GND 1AOUT Bias 1A L1 C6 L3 C10 TVS C15 T1 C11 C1 4 5 2AOUT 13 2BOUT 12 Bias 1B 1BOUT GND 11 10 9 C8 C12 C13 C9 C7 L4 L2 C14 T2 RF OUT C2 R1* R3* C3 6 7 8 IDD Adjust (+24 V) C5 Figure 8: Evaluation Board Schematic * Refer to Table 5 for R1, R3 use at lower IDD operation. 8 Data Sheet - Rev 2.1 12/2002 +24 V ACA2407E Table 6: Evaluation Board Parts List R EF C 1, C 2, C 3, C 6, C 7, C 10, C 14 C 4, C 5, C 8, C 9 C11 C 15 C12, C13, R2 TVS L1, L2, L3, L4 R1(5) R3(5) CONNECTOR (1) (4) DESCRIPTION 0.01 F Chip Cap 470 pF Chip Cap 0.5 pF Chip Cap 47 F Elect. Cap Not Used TVS 24 Volt 600 Watt 680 nH Inductor 75 k Resistor 10 k Resistor 75 N Male Panel Mount Ferrite Core Wire Printed Circuit Board (3) QTY 7 4 1 1 VENDOR MURATA MURATA MURATA DIGI-KEY CORP VENDOR P/N GRM39X7R103K50V GRM39X7R471K50V GRM36COG0R5C50 P5275-ND 1 4 1 1 2 2 DIGI-KEY CORP COILCRAFT DIGI-KEY CORP DIGI-KEY CORP PASTERNACK ENTERPRISES FAIR-RITE MWS WIRE IND. SMBJ24ACCCT-ND 1008CS-681XKBC P75KGCT-ND P10KGCT-ND P E 4504 2843002702 T-2361429-20 24V X 1A C 50 14996Y T1, T2 (2) (BALUN) 1 1 STANDARD PRINTED CIRC. INC INDIUM CORP OF AMERICA INDIUM 300 X 160 Mils Notes: (1) N connector center pin should be approximately 80 mils in length. (2) T1, T2 balun: 6.5 turns thru, as shown in Figure 9. (3) Due to the power dissipation of this device, the printed circuit board should be mounted / attached to a heat sink. (4) 400 mA minimum current rating. (5) Refer to Table 5 for R1, R3 use at lower IDD operation. Metalized traces on P.C.B. Pin #1 Keep leads twisted Wrap-around metal at corners - or vias Figure 9: Balun Drawing Data Sheet - Rev 2.1 12/2002 9 ACA2407E PACKAGE OUTLINE Figure 10: S7 Package Outline - 16 Pin Wide Body SOIC with Heat Slug 10 Data Sheet - Rev 2.1 12/2002 ACA2407E NOTES Data Sheet - Rev 2.1 12/2002 11 ACA2407E ORDERING INFORMATION ORDER NUMBER A C A 2407E S 7P 2 A C A 2407E S 7P 0 TEMPERATURE RANGE -40 oC to +110 oC -40 oC to +110 oC PACKAGE DESCRIPTION 16 Pin Wide Body SOIC with Heat Slug 16 Pin Wide Body SOIC with Heat Slug COMPONENT PACKAGING Tape and Reel, 1500 pieces per Reel Plastic Tubes, 25 pieces per Tube ANADIGICS, Inc. 141 Mount Bethel Road Warren, New Jersey 07059, U.S.A. Tel: +1 (908) 668-5000 Fax: +1 (908) 668-5132 URL: http://www.anadigics.com E-mail: Mktg@anadigics.com IMPORTANT NOTICE ANADIGICS, Inc. reserves the right to make changes to its products or to discontinue any product at any time without notice. The product specifications contained in Advanced Product Information sheets and Preliminary Data Sheets are subject to change prior to a product's formal introduction. Information in Data Sheets have been carefully checked and are assumed to be reliable; however, ANADIGICS assumes no responsibilities for inaccuracies. ANADIGICS strongly urges customers to verify that the information they are using is current before placing orders. WARNING ANADIGICS products are not intended for use in life support appliances, devices or systems. Use of an ANADIGICS product in any such application without written consent is prohibited. 12 Data Sheet - Rev 2.1 12/2002 |
Price & Availability of ACA2407E
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |